How Hyundai EQUUS Code P0019 Works?

How Hyundai EQUUS Code P0019 Works?

How Hyundai EQUUS Code P0019 Works?

Model: Hyundai EQUUS

Year Model: 2011

Fuel: Gasoline

Displacement: 4600cc

 

P0019 Crankshaft Position – Camshaft Position Correlation (Bank 2 Sensor B)

Study Guide and Component Location Study Guide and General Description Study Guide a Crankshaft Position Sensor (CKPS) is a magnetic type sensor that generates voltage using a sensor and a target wheel mounted on the crankshaft. Study The PCM calculates engine RPM by using the sensor’s signal and controls the injection duration and the ignition timing. Study the Camshaft Position Sensor (CMPS) is a hall sensor and detects the camshaft position by using a hall element. It is related with Crankshaft Position Sensor (CKPS) and detects the piston position of the each cylinder which the CKPS can’t detect. This Study CMPS signal is sent to the PCM and it uses CMPS signals for determining the ignition timing with CKPS signals. CMPS makes Sequential Injection possible. Study Guide and DTC Description If theStudy deviation between CKPS and CMPS(EX-CMPS Bank 2) is bigger than the threshold value, ECM sets DTC P0019. Study Guide and DTC Detecting Condition Item Detecting Condition Possible Cause Case1 Study DTC Strategy • Camshaft install diagnosis • Poor connection • Contamination of Oil / Clog of Oil path • CKPS, CMPS • OCV • CVVT Enable Conditions Study • First firing detected after ECM installed or ‘Camshaft install fault exist • Adapted CMP - CMP < 2 Deg Threshold Value Study • | Adapted CMP – Set value |> 7 Deg Case2 Study DTC Strategy • Camshaft and crankshaft alignment check Enable Conditions Study • Adapted CMP - CMP < 2 Deg • Engine speed < 1500rpm • Engine load < 50% • ECT > 60C Threshold Value Study • | Adapted CMP – Set value – Adaped CMP during installdiagnosis | > 13 Deg Diagnostic Time Study • 6 camshaft rotations MIL On Condition Study • 2 driving cycle Study Guide and  Diagnostic Circuit Diagram Study Guide and Signal Waveform & Data Fig.1) Normal waveform of CKPS & EX-CMPS Bank 2 at idle. more trouble shooting and general description

How to Repair Genesis Coupe BK not Cranking

How to Repair Genesis Coupe BK not Cranking

How to Repair Genesis Coupe BK not Cranking

Model:

• Hyundai Genesis Coupe BK

Year of Model:

• 2011

Fuel:

• Gasoline

Displacement

• 3800cc

Condition

1. Engine not cranking sometime.

Note: These is the 2nd time for me to encounter a the same trouble.

Study Guide and Cause

1. Due to PDM(Power Distribution Module)

Study Guide and Diagnosis

1. Scan tool check
   = No trouble code
2. Test the car to confirm the problem = OK the problem is confirm.
3. The same as the first trouble of coupe
4. Check with new good module
   =The Problem suddenly disappear after replace PDM.

Study Guide and Replace Parts

• Replace PDM ass.
• more information and

How to Repair Battery Indicator Lights On Code U1112

How to Repair Battery Indicator Lights On Code U1112.

 

2010  G 3.8 DOHC  Engine  Unleaded EOBD  U1112 LIN Communication Error

Auto Repair and Study Guide w/ Component Location Study Guide and General Description Many control units have applied to vehicle as it becomes more eletrolnical. These units control their own system based on information from diverse sensors. Therefore necessity of common use of diverse sensor information and importance of stable power supply are gathering strength. Battery sensor is mounted on battery (-) terminal. It transmits battery voltage, current, temperature information to ECM. ECM controls generating voltage by duty cycle based on these signals. Auto Repair w/ DTC Description ECM sets this code when there is an error in LIN communication line. DTC Detecting Condition Item Detecting Condition Possible cause DTC Strategy • Signal Monitoring • Open or short in LIN communication line EnableConditions • Engine Run Time  2sec. • Ignition Voltage  11V Threshold value • LIN communication error Diagnosis Time • Continuous MIL On Condition • NO MIL ON(DTC only) Diagnostic Circuit Diagram Signal Waveform & Data

More case and Repair Study

How to check Code C1202 Wheel Speed Sensor Front-LH Invalid/no Signal

How to check code c1202 wheel speed sensor front LH invalid/no signal

This Auto repair and Study guide was trouble encounter from Hyundai Genesis regarding on ECS/ABS light indicator on some times while driving. this was the trouble code appeared from the GDS C1202 Wheel speed sensor but some of trouble can not immediately caught base on the trouble code given by the GDS this is only the basis so that every technician has pattern.

Auto repair and Study guide This trouble was solve and the cause was only from the tire. all tire defective oblong that’s why the sensor from wheel can not give good signal.

Component Location,Auto repair and Study guide

 

Study guide General Description

Study guide The ESP system is the shorten word of Electronic Stability Program system. This system recognizes a critical driving condition by Yaw-rate sensor, Lateral acceleration sensor and Steering angle sensor. And then it stabilizes the Study guide and vehicle by a individual wheel braking and engine torque control through CAN communication. Among components of this system, the wheel speed sensor(WSS) is the essential component of the brake system. Study guide The ESP ECU(HECU, Hydraulic and Electronic Control Unit) uses the wheel speed sensor's signals to calculate a vehicle speed and also this Auto repair to determine whether a wheel lock occurs or not.

Auto repair DTC Description

Study guide of The HECU monitors the wheel speed sensor signal continuously and if the signal of a wheel speed sensor is omitted or too low, this DTC is set.

DTC Detecting Condition and Auto repair.

Item
Detecting Condition
Possible Cause

• Signal Monitoring

• Poor connection

• Improper installation of wheel speed sensor

• Abnormal Rotor and wheel bearing

• Faulty Wheel speed sensor

Threshold valve

• Vehicle speed = 10 kph(6.2 mph)

-Study guide and Auto repair when the maximum wheel speed is continuously over 10 km/h(6.2mph) and the other wheel speed is below 2 km/h(1.2 mph) for more than 180 seconds

• Vehicle speed = 15 kph (9.3 mph)

1. when the maximum wheel speed is continuously over 15km/h(9.3 mph) and the minimum wheel speed is below (0.4× the maximum wheel speed) for more than 120 seconds

2. when the maximum wheel speed is continuously over 40km/h(24.8 mph) and the minimum wheel speed is below (0.6× the maximum wheel speed) for more than 120 seconds

• when the brake pressure goes down or keeps up for more than 28 seconds as Study guide.

Fail-Safe

1.Only one wheel failure

: The ABS/TCS/ESP functions are inhibited.

The ABS/ESP warning lamps are activated, the EBD warning lamp is not activated.

2.More than two wheels failure

: The ABS/EBD/TCS/ESP functions are inhibited.

The ABS/EBD/ESP warning lamps are activated.

MORE INFORMATION AND TROUBLE SHOOTING

Study guide  and  Auto repair / Study guide and Auto repair / Study guide and Auto repair

How to Check ESP Code C1101 Battery Voltage High

How to Check ESP Code C1101 Battery Voltage High

Electronic Stability Program C1101 Battery Voltage High

Auto repair

Study guide

Study guide Component Location Auto repair and Study guide w/ General Description Study guide for the ESP system is the shorten word of Electronic Stability Program system. Study guide This system recognizes a critical driving condition by Yaw-rate sensor, Lateral acceleration sensor and Steering angle sensor. And then it stabilizes the vehicle by a individual wheel braking and engine torque control through CAN communication. Study guide The ESP ECU(HECU, Hydraulic and Electronic Control Unit) checks the battery voltage and alternator output voltage to determine, as a safety issue, whether this system can operate normally or not.Study guide The normal battery voltage range is essential for controlling this system as intended.   Study guide DTC Description The HECU monitors the voltage of battery and if it stays more than 17 Volts, this DTC is set. DTC Detecting Condition Item and Study guide Auto repair w/ Detecting Condition Possible Cause or Study guide DTC Strategy and Study guide • Monitoring the voltage of battery • Poor connection in power supply circuit • Faulty Alterator • Faulty HECU Threshold valve and Study guide • When Battery voltage is more than 17V Fail-Safe and Study guide • ABS/EBD/TCS/ESP funtions are inhibited. • ABS/EBD/ESP warning lamps are activated. Study guide and Specifications Normal Voltage Range IGN "ON" or Engine "ON" 10V ~ 16V more guide and Study Auto repair , Study guide , Auto repair , Study guide , Auto repair , Study guide , Auto repair